Remote Disaster Recovery Support for Clearbox
ClearBOX comes with a number of tools for remote support. This includes tools on the Compact Flash which allow for diagnosis, configuration, and repair of the ClearOS installation on ClearBOX.
Features of the compact flash currently include:
Bypass bootloader. This item tries to boot ClearOS without using the GRUB installation on the hard disks. This can be useful if GRUB is corrupt on that device.
Installation of ClearOS onto ClearBOX for single drive and dual drive systems.
Re-installation of ClearOS while preserving user data. ClearBOX uses bind mounts to store various user data directories on a separate partition. This re-install feature will preserve those points. You should still have a good backup.
NOTE: This option only works with systems configured with this version of the compact flash. If you purchased the system before Aug 2010 and did NOT re-install your system using this version of the compact flash, do not use this option. If you are unclear whether or not you can use this option, run the 'mount' command from command line. If it says: '/dev/mapper/data-data0 on /store/data0 type ext3 (rw)' then you are using a qualified system.
Includes image of 'Parted Magic', an open source graphical utility which allows for some disk diagnosis, repair, and imaging. This utility also has some remote control capabilities explained below.
Includes image of installation rescue mode.
Beginning with shipments of ClearBOX in August 2010, these utilities are already embedded on the compact flash included on the system. For older systems you can download the image here and use these steps to image the Compact Flash.
This will take a while to download as it is over 1 Gigabyte in size.
Run the following to make sure the image is untainted. Do not use the file if the file checksum is different than what is listed here:
dd if=ClearBOX-with-ClearOS52.image of=/dev/hda bs=512
Testing it out
Reboot the box and note the initial menu page for the boot loader. The only options here that are destructive are the installation and re-installation methods. The other are OK to test and run at any time.
Using Parted Magic
Parted Magic will boot into a graphical user interface. You should connect a USB keyboard and mouse to interact with the system.
Start the Network
To start the network, click the icon entitled, “Start Network”. You will be able to select the appropriate network type for your system. When the network comes up it may launch a browser to Google to show that it is working.
Enable Remote SSH
To enable remote SSH, click on the terminal icon down on the bottom bar (looks like a black monitor). Type the following to find your IP address:
Set the root password by running the following:
It will ask you to type a password. If you type a poor password it will complain that it is too weak but it will do it anyways.
To start the SSH server type the following:
You should now be able to remote SSH into the box as root using the password specified above.
Getting Output from Boot Screen
ClearBOX comes with a serial port that can be used for a modem or for other COM/Serial port related activities. The console cable is beige and has an RJ-45 jack on one end and a DB-9 on the other end and is configured as a NULL modem. The serial port is located:
In case of bad activity like a kernel panic, you can use this method to capture the data from the boot process. This data can then be transferred to USB and be read by parted magic when working remotely. To set this up, run Hyperterminal from your workstation and connect it to the serial port on ClearBOX using the cable provided. Set the data rates for 8-None-1 and disable flow control. When booting ClearBOX, proceed to the second screen (green) and stop the boot using the arrow keys. Highlight the kernel you are booting from and type 'e' to edit the line. Arrow down to the kernel line and type 'e' again. At the end of the line append the following:
Now when you boot, your output should display through the serial.
Fixing Partition Three
Partition three is designed to eventually provide the capability to boot your ClearBOX to a mode where gateway functions of your box are running and functional even if you hard drive is toast. This feature in on the current roadmap and will be implemented at some other time. If you received an error message while imaging the compact flash which stated that there was not any space left on the device, then you compact flash has a slightly different geometry from the original. To fix this, boot to your ClearOS system and start a command prompt. Run the following commands:
parted /dev/hda rm 3
Next run the fdisk utility to re-create partition 3.
You will get an interactive menu driven utility type the bolded characters at the appropriate time. If you get stuck type q to quit or CTRL+c.
The number of cylinders for this disk is set to 15538.
There is nothing wrong with that, but this is larger than 1024,
and could in certain setups cause problems with:
1) software that runs at boot time (e.g., old versions of LILO)
2) booting and partitioning software from other OSs
(e.g., DOS FDISK, OS/2 FDISK)
Command (m for help): n
p primary partition (1-4)
Partition number (1-4): 3
First cylinder (7890-15538, default 7890):
Using default value 7890
Last cylinder or +size or +sizeM or +sizeK (7890-15538, default 15538):
Using default value 15538
Command (m for help): w
The partition table has been altered!
Calling ioctl() to re-read partition table.
Completing the process
Finish up by formatting the partition:
This will format the partition. After it is done, confirm that your partition 3 exists by running:
fdisk -l /dev/hda
It should look similar to this:
Disk /dev/hda: 8019 MB, 8019099648 bytes
16 heads, 63 sectors/track, 15538 cylinders
Units = cylinders of 1008 * 512 = 516096 bytes
Device Boot Start End Blocks Id System
/dev/hda1 * 1 252 126976+ 83 Linux
/dev/hda2 253 7889 3849048 83 Linux
/dev/hda3 7890 15538 3855096 83 Linux